Bandit machine works clutches and belt drives and related parts, tools, and accessories for harley davidson motorcycles electricity lab activities

###########

BIG TWIN Sportsman Superclutch | Big Dog Bruiser Clutch and Bearing Carrier | Complete Superclutch Wet | Complete Superclutch Dry | Chain Drive Kits | Modular Belt Drives | Belt Drive Kits | Belt Drive w/Motorplate | Rear Pulleys w/Superclutch | Rear Pulleys | Front Pulleys Complete | Front Pulley Kits | Front Pulley Inserts | Lock-up Units | Tools | Bearing Hubs | One Piece Hubs | Center Hubs | Clutch Plates | Pressure Plates | Other Components

Retains stock shell, sprocket, and bearing. Includes center hub, snap ring and clutch pack (including – (1) thick steel backing plate, (8) thin steel driven plates and (9) Kevlar friction plates, pressure plate assembly, adjusting screw with lock nut, mainshaft nut, (6) spring cups, (6) standard springs, (6) heavy duty springs, (6) spring collars and (6) spring nuts). Ready to install. Will not accept lockup.

Chain primary drive only. Includes clutch shell with ring gear and sprocket, (12) drive keys with hardware, center hub, sealed double row bearing, snap rings, mainshaft nut and clutch pack (including – (1) thick steel backing plate, (10) thin steel driven plates, (9) friction plates of your choice, pressure plate assembly, adjusting screw with lock nut, (6) spring cups, (6) standard springs and (6) heavy duty springs, (6) spring collars, and (6) spring nuts). Some assembly required. Some clearance modifications to the inner primary case and primary cover are required. Will accept but does not include a lockup unit. gas mask art Installation of a lockup requires longer studs in the center hub – please specify when ordering clutch. Lockup will not fit in stock primary case. Please specify friction plate material when ordering. See section 35 for friction plate material selection information. All BANDIT Big Twin Superclutches work with stock chain drive components. See section 4 for chain drive components required for a complete new bike installation.

Chain primary drive only. gas relief while pregnant These use the same internal superclutch components described above, however the shell assemblies will accept an XR-750 style cover over the shell to allow the clutch to run dry when running a closed primary – recommended for ultra-high horsepower applications only. Will accept but does not include a lockup unit. Installation of a lockup requires longer studs in the center hub – please specify when ordering clutch. Lockup will not fit in stock primary case and will not allow use of XR-750 cover. Please specify friction plate material when ordering. gas bloating frequent urination See section 35 for friction plate material selection.

The Superclutch and lockup are completely adjustable for static spring load and centrifugal assist to allow tuning for optimum traction and still lock it up for top end speed. Used by racers demanding the best, it will do the same for you. We put our 3 finger lockup on top of our famous Superclutch which has larger bearings and 12 hardened drive keys to support the friction plates, and has been used to set drag racing records and win championships around the world for 20 years.

Options, options, we’ve got options. In addition to the choices already listed, we also have the offset option listed below, we can supply all the parts (except pulleys) in a natural machined aluminum finish, and we can custom build items to your order. The Bandit Superclutch and Superclutch II Beltdrives are also available as upgrades to fit other brands of belt drive motorplates, call for specifics for your motorplate. gas x reviews ratings More choices are on the way, check here for updates.

Three Sprocket shaft nuts are available, #1 at left is plated steel, standard equipment on drives where the nut us exposed. #2 at center is Stainless steel and incorporates a flange to eliminate the need for a washer. #3 at right is also stainless and has a decorative hex broached into the end. These nuts are compatible with other belt drives.

Includes the same internal superclutch components described under complete superclutch assemblies, installed in a BANDIT 8x85mm belt drive. Includes the following: A billet front pulley w/insert and hardware, an 8mm pitch X 3.35’’ wide HTD drive belt, a billet rear pulley with bolt-in drive keys and superclutch installed. Will accept but does not include a lockup unit – see section 12. Please specify friction plate material desired when ordering. See section 35 for friction plate material selection.

NOTE: These belt drives are for custom installations by experienced builders and often require modifications to stock chassis and components. The front pulleys fit all splined Big Twin engine sprocket shafts, and the application description indicates the transmission used. gas monkey live Also available with kit front pulleys with a variety of tooth counts for custom applications, and with standard or long spline pulley inserts – specify when ordering. These belt drives will NOT fit inside stock primary cases. No provisions for electric start are provided, but these drives will work with Tech Products electric start kits. See section 6 below for electric start belt drive/motor plate kits. For safety, we recommend the use of a belt guard with all belt drives.

Intended for custom applications or to upgrade older belt drives. Includes rear pulley, (12) drive keys w/hardware, center hub, sealed double row bearing, snap rings, mainshaft nut and clutch pack (including – (1) thick steel backing plate, (10) thin steel driven plates, and (9) friction plates of your choice, pressure plate assembly, adjusting screw w/lock nut, (6) spring cups, (6) standard springs and (6) heavy duty springs, (6) spring collars, and (6) spring nuts). Some assembly required. Please specify friction plate material desired when ordering. See section 35 for friction plate material information. For use with 8mm HTD belts only. electricity generation by country Does not include front pulley or belt. Accepts but does not include lockup unit. See section 12 for lockup information. Open primary only.

Features a billet front pulley machined for an 8x85mm x 3.35” wide belt with sufficient material available to achieve up to ¾” offset. Includes heat treated tool steel insert splined to fit a Big Twin sprocket shaft, socket head cap screws, sprocket shaft nut and washer. Customer is responsible for machine work to set offset and install insert. grade 9 electricity test and answers BANDIT MACHINE WORKS offers offset machining for an additional charge. Add the tooth count you desire to the part number – for example, a kit for use with an alternator with a 49 tooth pulley is PN 155421-49.

Used in superclutches with two piece bearing / center hub. Includes studs. Hub is splined for steel plates. Please specify if used with a BANDIT or MTC lockup. Center hubs for RaceCase Automatics can use a BANDIT Lockup PN 054501, PN 077501, or an MTC. Be sure to specify which Lockup you are using. The aluminum hub saves 1lb. 6oz., has a limited service life and is for limited use, maximum effort, high maintenance racing use only.