Catalog cronite bp gas prices akron ohio

#########

These pins have a tongue which is adjustable in length to suit all situations. Three prongs hold the pin to the feedboard. The sharp center prong is pushed through the feedboard 1/4″ behind the feedline. Two teeth on the other end should be forced down after registration is obtained. Some operators also glue the pins in position with sealing wax. Extra tongues and directions included. Sold by the box holding 12 pieces.

Adjustable quads are held in place by a locking lever that is raised and lowered to squeeze the feedboard. For each Quad Guide, make one or two slits of about 1” in length between ¼” and ¾” from and parallel to the feedline. Slide the guide under the slit at the front into register position. After adjusting for register, lock the guide into place by lowering the lever. Three extra tongues and instructions included. Sold in sets if three with three additional tongues.

Permits fast and easy gauge changes, reducing time and effort compared to conventional methods. The gaugeboard screws down onto the original wooden center feedboard, and is fitted with adjustable gauges. Locking screws quickly secure the gauges in position. A cutout finger hole permits the press operator to remove the stock easily after stamping. This metal board saves money by eliminating feedboard costs. Gaugeboard comes with 3 sets of gauges and posts, and installation and operating instructions.

Adheres layers of counterboard together and the counter to the counterblock slide. electricity outage austin Dry adhesive is applied like a big crayon and creates its best bond after pressure has been applied. It can be pulled apart or separated when heat is applied, which is handy for “patching” an impression or for removal from the slide. Most of the strength of a counter made with Prout’s Glue is horizontal to the press’s force. The counter will not slip sideways. electricity laws uk No “drying” time is required and a counter can be cut immediately after being glued.

Ideal for holding 18 gauge or 16 gauge plates at the proper height in the die chuck. Plates may be mounted to the plateholder with glue or double faced tape. The regular plateholders are usually supplied with a single rear rail, but additional rails may be added on the sides. Please specify the exact size of the plate when ordering the plateholder.

Inexpensive blue-colored solution provides a quick, reliable means of detecting worn chrome plating on steel dies. A worn area will quickly change to a copper color. Some operators perform this test every few thousand impressions so they can strip and re-plate their dies and plates as soon as the plating shows wear. Using this method, the life of a die may be prolonged indefinitely. 8 oz. bottle.

A very aggressive cleaner which will dissolve dried and hardened ink which was previously “impossible” to remove. Blast Away will also clean dirt from dies, fountains, presses, and floors. It must be thinned with at least 3 parts of water to be used at its greatest strength. Environmentally clean, biodegradable, and very strong. Should be mixed and may be transferred to a spray bottle.

Transfers ink from the large fountain roller to the die. Cronite offers ink rollers made from Urethane. Urethane ink rollers are available in 2-1/4″ diameter and they have a 5/8″ diameter hollow steel core. The rollers are sold by the inch, up to 21″ maximum length of an uncut roller. The rubber ends also can be cut back to expose the steel core around which stockinette can be attached.

A textured ink roller which eliminates the need for stockinette on most jobs. The tiny pockets created by the texturing on the roller bring a large quantity of ink to the plate when needed. As no stockinette is needed, there is no need to expose the core on the Diamond Textured Ink Roller. This product will save you money by shortening press set up time.

An instrument that determines the exact depth of an etched or engraved area. The indicator has an adjustable dial for easy calibration. Easy-to-read 2″ diameter dial has .0005″ calibrations, with enough space between each calibration so the user can further interpolate his reading. The body is chrome plated. gas pain in shoulder Each indicator is sold with a spare point and precision ground steel block used to zero the gauge accurately.

After protective greases are removed from dies or plates with a product such as kerosene or varsol, Wood Alcohol is used for final cleaning. Cronite’s “commercially pure” Wood Alcohol will leave your dies clean and free of any residues which could contaminate the surface to which the etching ground (acid resist) is to be applied. Usually, the alcohol is rubbed on with a lint-free clean cloth. It is allowed to evaporate, taking with it any petroleum residues.

A comprehensive training guide for the engraved stationery die stamping trade which describes the process so that even a beginner can understand. The guide presents an efficient, safe method for hand feeding Carver, Modern, and Waite die stamping presses. It also describes procedures for engraving copper, brass, zinc, and steel plates. Everyone should read it. We give a copy with each new press sold. 34 pages, illustrated.

Fast-drying, dark liquid acid resist for all metals. zyklon b gas effects When applied properly, one can easily see through it to the metal surface. It can be used in an etching machine because the surface is tough and won’t rub off or chip. Janes Ground is usually poured on the metal directly from the can. Then the metal is tipped in all directions until the area to be etched is fully covered. Excess ground may be poured back into the can from the corner of the metal plate. If necessary, thin with Ether. The ground may be removed with Wood Alcohol. Flammable liquid. 15 oz. can.

This red liquid is used to make any necessary corrections to the traced or scratched image on the ground covered die prior to etching. Stop Out Wax should be applied with a good red sable Stop Out Brush. Thin it with a small amount of quality alcohol. After etching, the Stop Out Wax can be removed with alcohol, along with the mechanical acid resist. Flammable. 4 oz. bottle.

A light blue corrosive liquid with a nitric acid base that effectively etches steel and brass. It is specifically formulated for hand etching with an acid brush. This is the best steel acid in the world, used in many other industries from gun and knife engraving to chemical milling of large dies and molds. The acid contains heavy metals such as silver and mercury, requiring proper disposal even when the acid is “spent”. The acid works so well because as it etches down the sides of the cavity, the walls are electroplated by the heavy metals attracted to the steel. Keep the acid out of direct sunlight if stored for long periods.

A dark, caramel colored acid used for etching various metals. It is available in 30° and 42° Baumé densities. Recommended for use in etching machinery of all types, but it can be brushed on by hand with an acid brush. Ferric chloride is the by-product of hydrochloric acid pickling of iron usually being descaled in a steel mill. It is important that there are no silicone additives used as anti-foams in the acid. It is possible to reclaim ferric chloride, but for the engraver, we recommend only virgin engraver’s grade acid.

A clear and flexible, colorless film of a special hardness that permits scratching by tools, but also resists abuse. It is used to transfer an image from one surface to another—from sketch to plate, plate to plate, or one sheet of gelatin to another. Gelatin sheets can save you time and effort when reversing or exactly duplicating images. 7″ X 17″, .006″ thick.

Cronite modifies a standard blender with titanium blades, arbor, and hardware. The bearings are of a special space-age material for acid resistance and heat of this high speed operation. The high speed agitation will completely dissolve Protectone in seconds and eliminate any hand mixing. 110V, 60Hz power, can be transformed to 220V European voltage with transformer #YP1-169.

Coating remover for Cronite’s Safecoat Steel plates or Hydro-Coat Copper and magnesium, or AQ-Blue plates. CPRS #2 is low odor and non-flammable and therefore is much healthier to use than most competitive products. electricity song CPRS #2 is water based. It will also remove the epoxy coating of the back of backcoated metal plates (if left in the solution for a long time) to prepare for chrome plating.

For background work or for shading in areas, special line gravers are available. They allow the engraver to cut several uniform lines at a time and can be used for a variety of purposes. Many sizes of these are available on a special order. The gravers we supply are made of tool steel. High Speed steel gravers which are much tougher are available quickly on an as required basis. Please ask us for High Speed steel when you want the best.

Small chrome plated metal graver-holding fixture used to sharpen gravers quickly and accurately. Three adjustable settings let you sharpen any graver to any desired angle. Use with a sharpening stone, sold separately. A properly sharpened graver is essential to produce a good engraving. The sharpener is sturdy and will last a lifetime. Directions included.

The easiest way to finely scratch through acid resist when etched lines must be marked in by hand. The diamond point also works well for tracing picture work on gelatin or for dry point or scribing work. Retractable Diamond Point is at 60 o angle, set in a chrome-plated pen-like holder with a pocket clip. Retraction protects the fine point if the tool is dropped.

Used to smoothly polish a particular metal surface area. Scratches, streaks, or errors on a die can be removed by burnishing. current electricity examples The tool is drawn back and forth across the surface with long, even strokes at right angles to the burnisher’s length. A clean, thin oil will help to lubricate this action as the metal is smeared or pushed around by the tip.

The T Square is used for laying out work on dies or plates. We manufacture fixed head and swivel head models. Both have low profiles to clear a 1/2″ die height, but the swivel head model has a low enough profile on the swivel side to be able to clear a 1/16″ thick plate. With the Swivel Head T-Square, a layout can be made at any angle. gas in stomach Each model has a brass head and an 8″ spring steel leg This is definitely a required tool for an engraver.

For use in an engraving machine or pantograph, the tracing point is attached in the hand piece of the tracing arm. The operator places the Tracing Point in the groove of a Masterplate’s character so that it may be traced accurately. The sharp tip is concentric to the outside of the point’s body, so the character will not become distorted if the operator rotates the hand piece.

The 3/16″ diameter by 2-7/8″ long Engraving Machine Diamond Point scratches through acid resist which has been applied to a die prior to etching the image. The Diamond Points are ground to a perfect conical point at a 60 o included angle. Care must be taken not to lower the point onto the die too rapidly, or the Diamond Point may fracture. Sold individually.

Most Masterplates have an alphabet pattern etched into them. The guide lines permit a pantograph machine’s tracing point to make properly spaced words. Made of tool steel 3-3/8″ wide, 19″ long, and .050″ thick. Masterplates are chrome plated to add to their longevity and rust prevention. Over 330 letter styles are available. These can be seen in the Engraver’s Letter Styles Booklet sold as Part No. EB1-203 and ordered by their part number.

Celluloid can be cut very easily and will withstand several dozen tracings if care is used. They are clear, with one side frosted and the other side smooth. Making a Celluloid Masterplate is quick and easy. The engraver traces a forward image on the frosted side with a lead pencil, then turns over the blank to hand engrave the image using the tracing from the other side as a guide. Each plate is sold individually.

Emery is a natural composite of corundum and iron oxide. The particles are cubical and tend to produce a polishing action while material is being abraded. Although the fine Emery Cloth has a grit value of 150, it cuts relatively quickly, while leaving a smooth polished surface. Grit values available are fine and medium in 9-1/2″ X 11″ sheets. Sold in individual sheets or by the dozen.

Our specially selected grade of willow charcoal is a fine abrasive, chemically treated for use on copper. grade 6 electricity project It will not put deep scratches on your plates. With the charcoal held vertically, rub the end of the grain against the metal. Lubricate with kerosene or gasoline mixed with a little oil. Store the charcoal in that same oily mixture in a covered jar so the charcoal will soak up the lubricant. Sold in individual sticks approximately 1-1/8″ X 1-1/8″ X 3-1/2″.

A specially formulated steel with a higher carbon content. The steel can accept transferring from transfer rolls and hardens more thoroughly than Cronite’s 1/4″ Engraver’s Steel. Maximum size available is 20″ X 25″. The grain direction should be specified when ordering. If desired, the edges can be beveled as required for some printing machinery.

Coated with a negative-working resist which is protected by a light-blocking plastic masking sheet. This presensitized copper works with a positive film. It offers the distinct advantage of a very smooth surface beneath the presensitized coating for perfectly photoengraved fine lines and delicate screens. Because the copper uses a solvent developer, shelf life is much longer than that of material that uses water-based developers. Has an enamel backcoating.