How to install a new efi gas tank in a 1960 corvette

Our new tank arrived complete with a flange for the in-tank fuel pump and the internal windage tray to ensure the pump would have a reservoir of fuel to pull from while in turns and during heavy acceleration and braking. Grade 9 electricity quiz It should be noted that TANKS Inc. Electricity terms and definitions also sells standard, exact duplicates of original tanks for carbureted applications. Electricity jeopardy game Our tank order came complete with a rollover safety vent and the proper fuel pump for our EFI application.

In keeping with the new products line of thinking, we ordered a set of new tank straps, tank pads and a filler neck hose and clamps from Corvette Central. Electricity usage by appliance Finally, we ordered a soft top protector from Corvette Central that was glued to the top of the gas tank cover. Gas nozzle prank This will protect your soft top and also add some degree of sound deadening to the cover. Electricity load shedding We already had the proper fuel line hose and fittings from FAST so we were prepared to begin the installation.

Our old tank was out of the way and sold at a swap meet so we had an empty tank cavity awaiting our new tank. Gas efficient suv 2015 First, we scraped the remains of the original tank pad off the floor and installed the new pads in the same place. Electricity generation by state Next, we set about test-fitting the new tank.

When Chevrolet built the 1960 Corvette, some of their tolerances were “generous” by today’s standards, think panel fit and door gaps. Electricity 101 presentation However, when they designed the fuel tank they decided to make it fit like the proverbial glove and since the TANKS, Inc. Electricity year invented unit is an exact duplicate it too is a very snug fit. Gas 85 As a matter of fact, we had to bend one or two corners with a pair of adjustable wrenches to provide clearance in the tank opening. Electricity and magnetism connect to form Do this very gently and a little at a time to provide the perfect clearance. Electricity 24 hours In the end, the tank fit perfectly but the cavity is so tight that we actually used the straps to pull the tank down the last 1/2-inch or so into the final, proper position.

Once the tank fit in the cavity we spent time cutting the pickup tube and return tube on the fuel pump to the proper depth, as per the excellent TANKS, Inc. Electricity news in nigeria directions. Gas 1940 hopper Satisfied that we had the fuel pump assembled properly, we installed the pump in the tank prior to actually installing the tank in the car. Electricity 4th grade powerpoint We installed the gas gauge sending unit in the new tank at the same time.

The next challenge was to fit the tank in the tank well with the straps hooked to the front tabs under the floor. Save electricity images Since I was working alone, keeping the tank straps in place was a bit of a challenge. Electricity nyc The straps were held in place with pieces of twisted wire, and then the tank was installed. Electricity cost nyc This took several tries, proving it would be much easier to have an extra set of hands for this part of the job. Gas x strips walmart The tank straps were bent to the contour of the tank and folded down toward the rear of the car. Electricity symbols and meanings The strap kit comes with a set of 5/16×2-inch bolts but the new straps must first be pulled down to the shape of the tank. Electricity rates el paso To that end a 4-inch, full-thread bolt was sourced and used to pull the straps down on the tank. Types of electricity tariff After the straps were formed to the tank the long bolt was removed and the 2-inch bolts that came with the kit were installed. Electricity symbols ks3 And that is how the installation would go in a perfect world.

Actually, our installation didn’t go quite that smoothly. Gas usa While we had taken the time to run a tap through the original threaded receivers it seems we under-estimated the rust damage on these small units. Gas jockey As we tightened the straps down they simply pulled out of the rivets and came apart. Electricity news australia It seems when Chevrolet assembled the 1960 Corvette they didn’t properly paint any of the steel pieces attached to the fiberglass body, and in fairness they were not too concerned about any part of the car lasting 56 years.

We had a similar problem with the front tank mounts and so we fabricated all new mounts from stainless steel. Gas efficient cars 2016 Our new pieces follow the original design but are not exact duplicates. Electricity worksheets for grade 1 If you are restoring your car or prefer to avoid the fabrication work, replacement mounts are available from your favorite vintage Corvette parts suppliers. Electricity 80s song We fabricated the pieces and bolted them in place with stainless steel hardware, knowing the parts would now last a lifetime.

We completed one non-fuel related task next. Electricity in indian states We took the time to install Dynamat over the inner wheelwells as this area would not be accessible later. Electricity in human body wiki Tires are a major source of noise in a car and this should go a long way to keeping any tire roar out of the cockpit.

The straps were then reinstalled for the last time and tightened down. Physics c electricity and magnetism study guide Next up was venting the tank. 4 gases in the atmosphere besides oxygen and nitrogen If you purchased an original-style tank from TANKS, Inc. Gas works park seattle the factory original vent hose would simply push in place, exit out by the gas filler and the job is done.

Since we are using the in-tank pump we would be using the rollover vent supplied with the tank. G gas lol Finding a good location for the rollover vent took a while but we finally located the vent in the passenger-side rear wheelwell. Gas lighting urban dictionary We fabricated a simple bracket, mounted the vent and connected the 3/8-inch hose. B games zombie This required drilling a hole in the fiberglass tank cover using a Uni-bit for a smooth cut.

Finally, we installed the -6 AN fittings into the feed and return lines on the in-tank pump and routed the proper FAST high-pressure fuel-injection hose across the top of the tank and down to the framerail, following a similar route as the original fuel line. Gas bijoux soho We fastened the feed and return lines to the outside of the framerail using stainless steel Adel clamps, and brought the fuel lines into the engine bay.

Next, we installed the new filler hose, filler neck grommet and filler tube inside the gas filler door and onto the tank. C gastronomie vitam This was a very straightforward process and the Corvette Central parts fit perfectly.

The final piece of the puzzle was fitting the factory fuel tank cover over our new tank. Electricity nw Once again, if you are using an original-style tank for carbureted engines the cover will simply bolt back in place. Electricity prices by state With the in-tank pump installed we encountered some contact between the pump and the cover. Gas exchange in the lungs occurs in the Our concern was the pump could transmit noise through the contact point of the cover so we opted to raise the forward edge of the fiberglass cover 1/2-inch. Gas pump icon We achieved this by using a piece of 1/2-inch box tubing and secured it to the original mounting flange with sheetmetal screws. Electricity definition physics We drilled a 3/16-inch hole through the box tubing in four places. 100 gas vs 10 ethanol Then we opened the top hole up to 3/8 inch while leaving the lower hole 3/16 inch. H gas l gas This allowed us to us sheetmetal screws to secure the box tubing to the original crossbrace and all the sheetmetal screws were located internally in the box tubing, which left a smooth top mounting surface for the fiberglass cover. Gas hydrates india We also welded a tab on each end and secured it to the 3/8-inch bolt on the seat back brace. A gas station near me This made a very secure mount and even added some stiffening to the area.

The cover was then bolted down using the original bolt locations on the rear of the cover and a series of sheetmetal screws into the box tubing on the leading edge of the cover. Gas emoji meaning We used a gasket between the cover and the mounting surfaces in an attempt to make an airtight fit as early Corvettes seem to be known for gas odors. Gas exchange in the lungs takes place in the Strip caulking is also available from Corvette Central for sealing the cover and may actually work better than our gasket material. Gas problem in babies Since we raised the forward edge 1/2-inch, we used two pieces of soft, compressible foam rubber to form a transitional seal up to the front edge. Static electricity definition science Then the soft top protector from Corvette Central was glued on top of the cover and the job was complete.

In the end we couldn’t be happier with the tank from TANKS, Inc. Gas yojana and the new pieces from Corvette Central and our fabricated brackets. Gas examples matter It did take us a bit longer than we expected, but then most things do when you’re working on a finished, painted car. Electricity ground explained We now have a brand-new fuel system that will serve us well for many years to come.