## Led circuit – wikipedia hp gas kushaiguda phone number

#

The simplest circuit to drive an LED consists of a voltage source and two components connected in series: a current limiting resistor, sometimes called the ballast resistor, and an LED. Optionally, a switch may be introduced to open and close the circuit. Although simple, this circuit is not the most energy efficient circuit to drive an LED, since energy is lost in the resistor. More complicated circuits improve the energy efficiency.

An LED has a voltage drop specified at the intended operating current. Ohm’s law and Kirchhoff’s circuit laws are used to calculate the appropriate resistor value to obtain the desired current. The value is computed by subtracting the LED voltage drop from the supply voltage and dividing by the desired operating current. If the supply voltage is equal to the LED’s voltage drop, no resistor is needed.

The voltage versus current characteristics of an LED are similar to any diode. Current is approximately an exponential function of voltage according to the Shockley diode equation, and a small voltage change may result in a large change in current. If the voltage is below or equal to the threshold no current flows and the result is an unlit LED. If the voltage is too high the current exceeds the maximum rating, overheating and potentially destroying the LED.

It is therefore important that the power source provides an appropriate current. LEDs should only be connected to constant-current sources. Series resistors are a simple way to passively stabilize the LED current. An active constant current regulator is commonly used for high power LEDs, stabilizing light output over a wide range of input voltages which might increase the useful life of batteries. Low drop-out (LDO) constant current regulators also allow the total LED voltage to be a higher fraction of the power supply voltage. Switched-mode power supplies are used in some LED flashlights and household LED lamps. Series resistor [ edit ]

Miniature indicator LEDs are normally driven from low voltage DC via a current-limiting resistor. Currents of 2 mA, 10 mA and 20 mA are common. Sub-mA indicators may be made by driving ultrabright LEDs at very low current. Efficiency tends to reduce at low currents [ citation needed], but indicators running on 100 μA are still practical.

LEDs can be purchased with built-in series resistors. These can save printed circuit board space and are especially useful when building prototypes or populating a PCB in a way other than its designers intended. However, the resistor value is set at the time of manufacture, removing one of the key methods of setting the LED’s intensity. Series resistor calculation [ edit ]

where V s is the power supply voltage, e.g. a 9-volt battery; V f is the LED forward voltage (also referred to as the "voltage drop") across the LED; and I is the desired current of the LED. Both V f and the maximum recommended value for I are obtained from the LED manufacturer’s specifications. The above formula requires the current in amperes, although this is usually given by the manufacturer in milliamperes, such as 20 mA. Many circuits operate LEDs at less than the recommended maximum current, to save power, to permit the use of a standard resistor value, or to reduce brightness.

Typically, the forward voltage of an LED is between 1.8 and 3.3 volts. It varies by the color of the LED. A red LED typically drops 1.8 volts, but voltage drop normally rises as the light frequency increases, so a blue LED may drop from 3 to 3.3 volts.

Strings of multiple LEDs are normally connected in series. In one configuration, the source voltage must be greater than or equal to the sum of the individual LED voltages; typically the LED voltages add up to around two-thirds of the supply voltage. A single current-limiting resistor may be used for each string.

Parallel operation is also possible but can be more problematic. Parallel LEDs must have closely matched forward voltages ( V f) in order to have similar branch currents and, therefore, similar light output. Variations in the manufacturing process can make it difficult to obtain satisfactory operation when connecting some types of LEDs in parallel. [2]

Direct drive is the simplest-to-understand approach—it uses many independent single-LED (or single-string) circuits. For example, a person could design a digital clock such that when the clock displays "12:34" on a seven-segment display, the clock would turn on the appropriate segments directly and leave them on until something else needs to be displayed.

However, multiplexed display techniques are more often used than direct drive, because they have lower net hardware costs. For example, most people who design digital clocks design them such that when the clock displays "12:34" on a seven-segment display, at any one instant the clock turns on the appropriate segments of one of the digits—all the other digits are dark. The clock scans through the digits rapidly enough that it gives the illusion that it is "constantly" displaying "12:34" for an entire minute. However, each "on" segment is actually being rapidly pulsed on and off many times a second. Such multiplexed displays have net lower hardware costs, but the resulting pulsed operation makes the display inevitably dimmer than directly driving the same LEDs independently.

An extension of this technique is Charlieplexing where the ability of some microcontrollers to tri-state their output pins means larger numbers of LEDs can be driven, without using latches. For N pins, it is possible to drive n 2-n LEDs Polarity [ edit ]

Unlike incandescent light bulbs, which illuminate regardless of the electrical polarity, LEDs will only light with correct electrical polarity. When the voltage across the p-n junction is in the correct direction, a significant current flows and the device is said to be forward-biased. If the voltage is of the wrong polarity, the device is said to be reverse biased, very little current flows, and no light is emitted. LEDs can be operated on an alternating current voltage, but they will only light with positive voltage, causing the LED to turn on and off at the frequency of the AC supply.

Most LEDs have low reverse breakdown voltage ratings, so they will also be damaged by an applied reverse voltage above this threshold. The cause of damage is overcurrent resulting from the diode breakdown, not the voltage itself. LEDs driven directly from an AC supply of more than the reverse breakdown voltage may be protected by placing a diode (or another LED) in inverse parallel.

Many systems pulse LEDs on and off, by applying power periodically or intermittently. So long as the flicker rate is greater than the human flicker fusion threshold, and the LED is stationary relative to the eye, the LED will appear to be continuously lit. Varying the on/off ratio of the pulses is known as pulse-width modulation. In some cases PWM-based drivers are more efficient than constant current or constant voltage drivers. [4] [5] [6].

Most LED data sheets specify a maximum DC current that is safe for continuous operation. Often they specify some higher maximum pulsed current that is safe for brief pulses, as long as the LED controller keeps the pulse short enough and then turns off the power to the LED long enough for the LED to cool off. LED as light sensor [ edit ]