Low amp plasma welding i feel electricity in my body

##########

• A dark blue or black tungsten (Figure B) is a sign of moisture or oxygen getting into the plasma gas line (also called the pilot gas line). If the gas is good quality and the gas lines are leak free the tungsten should remain a gray color (Figure A) not dark blue or black. Moisture and oxygen in the gas lines deteriorate the tungsten electrode and thus the number of arc starts that the tungsten electrode can produce is reduced. electricity rates el paso This cuts down on the number of arc starts in production and decreases production.

• Any leaks in the gas lines or fittings can allow air to be sucked into the gas system which adds oxygen and moisture to the welding gases being used. Levels of oxygen and water should be less than 5ppm. The most important gas in plasma welding is the pilot gas, also called plasma gas, is always argon gas. The grade of argon being used should be at least 99.998% pure argon. In plasma welding if the gas is not pure it will contaminate the tungsten electrode and turn the tungsten electrode a dark blue and black color. If the problem is very severe the discoloration will run all the way to the point of the tungsten electrode and the nozzles on the torch will clog up.

• Tocheckforgasleaksoneneedstoinstallabottleofgasonthepilotgasline and it is recommended that the gas bottle is used with a dual stage regulator with a stainless steel diaphragm. Next take a nozzle for the torch and solder the orifice of the nozzle closed. Clean the nozzle after soldering with acetone or alcohol and install a small o’ring that will make a seal when the nozzle is screwed into the torch and hand tightened Also make sure that where the nozzle seats against the torch body is clean and free of dirt. z gas tijuana telefono If the nozzle does not seat well against the torch body a gas leak can occur. Turn the pilot gas flowmeter up to its highest flow and turn off the argon gas bottle. This will

trap gas in between the tip of the torch nozzle and the argon gas bottle. gaston yla agrupacion santa fe 2016 Take a reading on the high pressure gas gauge of the gas regulator. Wait 15 to 30 minutes. If the gas system is leak free the gauge reading will stay the same as when the gas bottle was turned off. If the gauge pressure drops then there is a gas leak in the system. The leak could be caused by a hole in the gas hoses or defective fittings and gaskets.

• After it has been determined that the gas system is leak free the system needs to be purged. electricity dance moms choreography By purging the gas lines it will clean all of the moisture and oxygen out of the lines so that you will only have good clean gas in the system. Turn the pilot gas flow up to its highest flow rate and let the gas run through the lines for at least 30 minutes to and hour. Next start a pilot arc and let it run at normal pilot arc gas settings (0.4 to 0.6 liters per minute) for 10 minutes. Turn off the pilot arc and check to see if the color of the tungsten electrode is gray. If it is gray your gas system is clean. If the color is black and blue then the system needs to purge longer to make sure it is clean.

• If your welding system is shut down over night air with oxygen and moisture will get up inside the plasma torch. Before starting to weld on the next day you need to again purge the gas lines approximately 5 to 10 minutes before starting to weld. electricity jewels You may want to turn the pilot gas down to a very low flow such as 0.1 liters per minute and let the gas run all night to keep the gas line clean. gas prices going up or down It will be such a low flow that it will not be of any economic importance.

• Whenever thinking about electrode life, electrode contamination, ease of arc starting and arc stability you should not forget that the exchange of ions takes place within the plasma column in both directions which is from the electrode to the work piece and from the work piece to the electrode. If impurities such as lead, sulfur, aluminum, magnesium, copper, zinc, brass, oil, grease or any other dirty elements are on or in the material being welded they will contaminate the tungsten electrode and nozzle. You then cannot count on a maximum number of welds before replacing the tungsten electrode and weld nozzle.

torch head that you do not over tighten the nozzle and strip the threads. Copper is a very soft material, which makes it easier to over tighten the nozzle. Tighten the nozzle until it barely makes intimate contact with the end of the torch head. It is recommended that pliers be used to tighten the nozzle but be careful not to grab the torch head with the pliers. Also be careful not to cross thread the nozzle. If the nozzle is cross threaded it will damage the threads inside the torch head. Do not get dirt, grease or oil inside the torch head or on the nozzle threads, which will damage the threads in the torch head. gas zombies If the torch head is damaged by the pliers it can cause a gas leak between the nozzle and torch head and the nozzle will not seat properly against the water cooled part of the torch head. If the threads are stripped and the torch head is damaged the torch will have to be replaced. gas finder mn Periodically clean the inside of the torch and thread where the nozzle seat with alcohol of acetone. Make sure that the technician that handle the torch and installs nozzles hands are clean. Dirt, oil, grease and grit is not acceptable on any of the torch parts. The plasma welding torch is an expensive device and should handled with great care.