Shapeoko 3 – shapeoko speedy q gas station

#########

1) The Sparkfun unit just has one y-axis motor controller (3 total controllers, not 4). The two y-axis motors are wired to this in parallel. 2) The Sparkfun unit has more versatile stepper motor configuration hardware: Microstepping increment options are 1, ½, ¼, and 1/8 (4-position switch instead of just 2). Stepper motor current is continuously variable from 1A to 2A using a rotary pot (instead of 2-position switch presetting current for NEMA 17 or 23 stepper coils)

Note that homing switches are now a standard part of the kit (but the instructions may not be fully caught up) — please see the instructions for the upgrade kit: http://docs.carbide3d.com/article/67-shapeoko-3-limit-switch-installation (arguably it’s easier to build and initially test the machine without switches, then install them when a project warrants them)

• XXL: 45″ (114.3 cm) W × 40 1/2″ (102.87 cm) L × 16″ (40.64 cm) H [11] (one user measured: 40 1/4″ (Y-axis) Front to back (from outside of black bracket on each end) × 44 13/16″ (X-axis) Left to Right (from outside of black bracket on each end). [12] "Actual foot print is 44.75″ wide 40.25″ deep. electricity and circuits ppt If you’re going to enclose it you would need more. Exact measurements for an enclosure would be 47.375″ wide and 45.5″ deep." [13] spacing of feet: http://community.carbide3d.com/t/adjustable-feet-spacing-on-s03-xxl/8780/2

• Z-axis: Cutting distance: ~2″ (50mm). Cutting range: 3″ (75mm). ideal gas definition chemistry These numbers will depend upon endmill selection and fixturing. It is possible to cut along the entire ~3″ for certain projects, esp. those which will fit in the overhang at the front of the machine. Total travel ~4.25″ [15] (add 30mm if DWP-611 is mounted to top set of holes) [16] Note that it is possible to mount stock at the front of the machine, or to cut a hole in the Wasteboard and cut things which otherwise would not fit. [17]

• Obtain a router, Dewalt 611 preferred DWP611 (note that that is the more common version w/ accessories, if not planning on using it as a stand-alone router, the DNP611 is perfectly serviceable and may be available for less) — Porter Cable 450 will fit as well [62] but lacks variable speed [63] — Makita RT-0701 and other 65mm diameter tools would require an adapter

• The Nomad uses an embedded motion controller so you won’t have to dedicate a computer to control the mill like some PC-based CNC machines. Just plug the USB cable into your Mac or Windows computer and you’re ready to go. If you have a favorite CAM program and don’t want to re-learn a new workflow, no problem. Carbide Motion can read gcode from any CAM program. [64]

• If we want to implement spindle control, what controller pins should be used for turning the spindle on (spindle enable) and for outputting the spindle speed? What needs to be configured in GRBL to use spindle enable and spindle speed control? I think we’ve been told that the 6-pin connector labelled SERIAL_PROGRAMMER has outputs for spindle control, but that we’ve not yet been given details of using spindle control. [74]

Regarding part number 13 (the two silver colored custom extrusions held on to the back of the plate with square nuts that engage in slots — strangely, they are listed in the parts but not identified in the drawing…). electricity equations physics It is important that these be parallel to the vertical axis of the plate, equidistant to each other at their tops and bottoms, and are pushed towards each other given the slop allowed with the v-groove wheels.

If they are not parallel to the plate, your router will not be perpendicular to the table. (This I learned the hard way.) [By the way, here’s how I figured that out: remove the router, make sure the power is off so you can move the carriages freely, and slide the z-axis all the way down to the waste board. Look where the x-axis carriage plate is touching the waste board — it should be contacting the waste board evenly.]

Open the box and lift out the top layer of foam packed parts. Compare the number of "bags" to the packing list above. electricity for beginners pdf No need to open any bags yet. Lift out the middle layer of foam packed parts and place it on the top layer. Admire the parts, and compare also. Left in the bottom of the box are the two waste board halves. Pull those out of the box and set them aside. Put both foam layers and parts back in the box. gasco abu dhabi careers I kept the box under my assembly table.