Supabrake-ii motorcycle tail light modulators vizi-tec electricity sound effect

This is our best selling product. More advanced than the SB1. It offers more options in terms of hardware and software. Example you can select from 10 different profiles. The SB1 has only one fixed profile. (Upgrade to the SB3 and get over 108K profiles!)

It’s a proven fact that motorcycles can decelerate more rapidly than most cars and trucks. The combination of a motorcycle’s narrow profile and the brisk change in velocity during braking is the most common cause of rear end accidents involving motorcycles, and often the results are fatal to the rider. Vizible Technologies’ SupaBrake modulators are designed to enhance the reaction time of the vehicle behind you. It is designed to pulsate your vehicle’s brake light(s) with a variable number of flashes calculated by its embedded algorithm. The algorithm is based on the rate at which you apply your brakes. As a result, the brake light(s) are flashed in a more subtle manner at lower speeds(when brakes are frequently used), and more aggressively at higher speeds(when brakes are not used for longer time intervals). Whereas other simpler products on the market that continuously "blink" their brake light(s) with an annoying repeating sequence – each and every time their brakes are applied! Our Supabrake product pulses in driving conditions when you need to get the immediate attention of drivers without annoying them.

Upon applying the brakes, the SupaBrake sends a burst of pulses to your motorcycle’s brake light(s). The duration of the burst is a function of the time elapsed between the current brake cycle and the previous. After the burst, the unit allows the rear brake light to function normally(solid brake light). This algorithm is designed to eliminate target fixation as found in cheaper, passive versions that continuously "blink" the brake light(s) even though the vehicle is at a complete stop.

When the frequency at which the driver/rider applies the brakes increases, (i.e. during low speeds such as city driving), the shorter the burst of flashes to the rear brake(s) light will be. If the brakes are applied within 0 – 12 seconds, the brake light will NOT flash – thus allowing it to function normally (solid brake light). This condition is most valuable during heavy stop-and-go traffic so as not to annoy the person or police in the vehicle behind you.

When the frequency at which the driver/rider applies the brakes decreases, (i.e. at cruising speed), the longer the burst to the rear brake light will be. This condition is most valuable during quick sudden decelerations at speeds which require quick reaction to changes in traffic conditions or other driver’s intentions. It has been scientifically proven that a quick flashing of a vehicle’s brakes will alert the driver behind much sooner … and the SupaBrake Flasher does this for you.

This feature allows the user to quickly “tap” the brake lever or pedal without the algorithm inducing its flash routine or resetting. In an event of a "tap", the brake light will function normally and will appear as an ordinary tap of the brakes. Another aspect to this feature is that it allows the user to initiate a quick speed check on the rear brakes before a full application of the front brakes. In this case the algorithm will trigger a burst after full brake application.

This technology, unique to Vizible Technologies, allows the rider to manually induce a flash routine after the initial application of the brakes. This is useful when stopped alone at a red light or in traffic to alert vehicles approaching from behind. Example: Press and hold the brakes for >3seconds. Quickly release and reapply the brakes within half second. The unit will output a burst of flashes.

Each pulse period is gradually increased from the previous pulse. This gives the given burst cycle a "de-acceleration" illusion when viewed from behind at speed. In other words, the routine will start with a faster frequency and end with a slower frequency.

Don’t put other outdated bulkier modules on your motorcycle that pulsate your brake light each and every time you apply your brakes. Most of these cheaper annoying modules will continue to flash your brake light(s) with the same irritating routine even when you are completely stopped in traffic. This is not only illegal and annoying it detracts from the visual appearance of your vehicle and other drivers/riders attention to the road. Some of these "zombie-like" flashers claim to have an accelerometer module that will supposedly give you a couple of hundreds milliseconds reaction time. We have experimented with these in our lab and road tests, they don’t work due to the nature of engine vibration, road vibration and mounting angle. Simply too many noise vectored components giving them very poor sensitivity. That is not the best way to implement this sort of technology. At best they are just for marketing. Be careful you always get what you pay for.