The pxie-517x family the first oscilloscopes with labview-programmable fpgas – national instruments electricity sources

############

PXIe-517x oscilloscopes use a low-power 14-bit ADC from Analog Devices that has excellent noise density. Using this ADC, NI engineers can include eight channels of 250 MS/s with very low noise into a single-slot PXI oscilloscope. The ADCs are not the only component that makes the PXIe-517x oscilloscopes possible. FPGAs continue to progress in number of logic cells, digital signal processing (DSP) slices, and I/O like mp electricity bill payment paschim kshetra multi-gigabit transceivers at an exponential rate while also decreasing the power required to use these features. Kintex-7 FPGAs from Xilinx provide the necessary processing power at the right power consumption to design the firmware of these reconfigurable oscilloscopes, whether that be the standard oscilloscope firmware from NI or your custom firmware designed with the LabVIEW FPGA Module.

Power usage was not the only challenge in designing these oscilloscopes. Eight ADCs collecting 250 MS/s of 14-bit analog data create an enormous amount of data—approximately 4 GB/s. Transmitting that much data with a traditional ADC that communicates over many parallel digital lanes would be incredibly resource intensive. The ADCs on PXIe-517x oscilloscopes use a high-speed serial physical layer and protocol 9gag wiki specific to data converters called JESD204. Using JESD204B, these ADCs can transfer many gigabits per second (Gb/s) of data to the Kintex-7 FPGA on the instrument.

Getting the analog data from the ADCs to the FPGA is only half the task. In many test applications, you must stream data from the oscilloscope to a host controller, peer data processor, or data storage. The PXIe-517x oscilloscopes use the Kintex-7 FPGA to stream data along the PCI Express backplane of the PXI Express chassis at up to 2.3 GB/s.

In many test systems, you must control the DUT or chip under test through digital signals. Traditional automated test systems can sequence through DUT modes and take the needed measurements in each stage. In some cases eon replacement gas card, automated test equipment (ATE) systems incorporate intelligence to progress between DUT settings according to the measurement values received.

In either scenario, software-designed instruments that incorporate a user-programmable FPGA result in cost and time savings. Consolidating measurement processing and digital control into a single instrument reduces the need for additional digital I/O in the system and avoids configuring triggering between instruments. In cases where the DUT must be controlled in response to measurement data received, software-designed instrumentation closes the loop in hardware and reduces the need for youtube gas pedal lyrics decision making in software at a significantly higher latency.

Today’s software-based test systems can perform a limited number of measurements in parallel, but software-designed instrumentation is limited only by the available FPGA logic. You can process dozens of measurements or data channels with true hardware parallelism, removing the need to choose between measurements of interest. With software-designed instruments, functionality such as real-time spectral masking is achieved with dramatically higher performance and at a fraction of the cost compared to traditional boxed instruments.

The low latency associated with performing measurements in software-designed instruments means that you can take tens or hundreds of live measurements and average them together in the same amount of time as a traditional test system requires to take a single measurement. This results in improved test-result quality and increased confidence in your measurements.

Traditional electricity storage cost per kwh instrument options for low-latency trigger behavior are fixed according to the hardware being used, but with software-designed instrumentation you can incorporate custom triggering functionality into your device to quickly zero in on situations of interest. Flexible hardware-based triggering means that you can implement custom spectral masks or other complex conditions as criteria for either capturing important measurement data or activating additional instrumentation equipment. See a custom trigger built with LabVIEW and implemented on a software-designed oscilloscope in this 5-minute webcast.

Instrument performance and flexibility are the most important features in science applications such as high-energy physics. Most of the signal processing and control tasks for these applications traditionally used analog electronics and relatively slow ADCs to capture preconditioned signals. Today, with gas 85 vs 87 fast high-resolution ADCs (14 bit and 250 MS/s and above) you can sample signals directly from sensors. Using instruments with user-programmable FPGAs, you can perform signal processing in real time during acquisition instead of in postprocessing on a PC. You get faster results and more flexible, efficient control in scientific experiments.

In particle accelerators and synchrotron machines, you have to monitor particle beams’ trajectories constantly to keep them on track with magnets that require the correct control input. Oscilloscopes with user-programmable FPGAs can help to solve applications like the DIII-D tokamak, because their fast and inherent parallel processing allows analysis of a signal and frequency domain at the same time, as well as very fast control loops. You can customize the FPGA to also monitor safety critical parameters to trigger a shutdown in case pictures electricity pylons the system enters an unwanted state.

Using the high-speed PXI Express bus, you can pair oscilloscopes with output modules that generate control signals for experiments or stream data continuously to a storage medium at speeds of more than 3 GB/s per instrument. Another benefit of user-programmable FPGAs is you can change the explained processing and control algorithm very quickly. You can load an already compiled bit stream into the FPGA in fractions of a second to alter the oscilloscope’s behavior.

For a more efficient way, reduce data to a minimum by deciding right at acquisition time which signals to keep and which to discard. Often the only parameters of interest are timestamps and calculated energy pulses, so returning these parameters from an instrument is more efficient storage-wise and enables longer measurements because the already extracted results can be easily offloaded to the host PC.

The measurement system’s tasks are to extract, time stamp, and measure the energy pulses and eliminate the time (acquired data) without pulses in between, often called zero-suppression. This is easy to implement in an FPGA because every sample can ag gaston birmingham 120 be evaluated in real time. The general architecture for detecting events as shown in Figure 4 would be a pulse—such as a threshold—detector, followed by algorithms that fit a reference pulse—such as a Gaussian shape—on the detected pulse for estimating the maximum value. After detecting and storing the peak and the corresponding timestamp, you can either discard the acquired pulse or send it to another buffer for further analysis or display on the PC.

LabVIEW FPGA provides users with the tools to implement the necessary signal processing steps on oscilloscopes to filter and shape pulses, count electricity prices going up and time stamp their occurrences, measure height and rise time, reconstruct baselines directly inside the instrument, and return the compressed results to a PC to make researchers more efficient in their work.

The lifespan of many aerospace and defense testers can reach 40 years and beyond. The challenges of replacing an obsolete instrument and recertifying a tester can be extremely costly. The reconfigurable nature of the PXIe-517x oscilloscopes makes them a good choice for new designs as well as drop-in replacements for obsolete instruments. Because many specifications or characteristics, such as triggers or filters, need to stay consistent through the generations of testers, these oscilloscopes help to alleviate backward compatibility issues that may arise by allowing you to reuse the hardware IP created in LabVIEW, helping to reduce both certification and maintenance gas weed strain costs.

Testing the new semiconductor devices that are making modern wireless revolution possible requires high resolution, speed, and flexible instrument performance. The channel density, high resolution, superb spectral performance, and user-programmable FPGA of the PXIe-517x oscilloscopes make them ideal tools for making many of the fast analog measurements needed in semiconductor characterization and production test systems.